عرضه و فروش انواع روغن های صنعتی در کشور
شماره تماس فروش
۰۲۱-۲۲۲۶۶۹۸۶
۰۲۱-۲۲۲۶۶۳۳۴
شرکت نفت شل، (به انگلیسی: Shell Oil Company) شرکت نفت و گاز آمریکایی و شعبه کمپانی رویال داچ شل در ایالات متحده آمریکا میباشد.این شرکت در زمینه استخراج نفت و گاز طبیعی، بازاریابی فرآوردههای نفتی، همچنین تولید محصولات پتروشیمی فعالیت میکند.شرکت نفت شل، با در اختیار داشتن بیش از ۲۵٫۰۰۰ جایگاه پمپ بنزین در ایالات متحده، مالک بزرگترین شبکه عرضه سوخت در این کشور میباشد. شمار کارکنان این شرکت حدود ۲۲٬۰۰۰ نفر است و دفتر مرکزی آن در هیوستون، تگزاس قرار دارد.
Shell Tivela Oils
Synthetic gear oils lor industrial applications
Shell nvela Oils are high performance, synthetic, industrial gear oils based on polyalkylene glycol and specially seleded additives. They are free of chlo rine, sulphur and lead based materials.
Applications
Enclosed Industrial Gear Units:
Bevel, spiral bevel, helical, enclosed spur and worm gears
Performance Features
Outstanding Load Carrying Properties Reduces gear tooth and bearing wear on both steel and bronze components
Excellent Thermal Stability
Resists degradation and sludging at high temperatures
ERective Corrosion Protection
Even in the presence of water
Good Demulsibility Characteristics
Rapid water/oil separation
Service Life
Shell Tivela Oils will remain homogenous from below the pour points to temperatures in excess of 250°C.
The anticipated service life is substantially in excess
of 1 0,000 hours at 100 o C in industrial enclosed gear units, making extended oil drain intervals possible.
Seal Compatibility
Polyurethane based elastomers, leather, cork, asbestos, paper and board should be avoided.
Other common seal and gasket materials are unaf fected by Shell Tivela Oils. Nitrile Rubber (NBR), Fluoro-Silicone or Vinyl-Methyl Polysiloxane (Q) are recommended especially where high temperatures are involved.
Ordinary industrial paints will soften in the presence of Shell Tivela Oils. Ideally, internal gearbox
Performance Specifications
Meets the requirements of:
David Brown Table G lubricants for industrial enclosed gear units.
Flushing Procedures
When changing from mineral oil to Shell Tivela Oil the following procedure should be followed:-
Run the system until the mineral oil is warm and then drain as fully as possible, paying particular attention to reservoirs, lines etc., where oil may be trapped. The system should be cleaned of residual sludge.
Flush the system with the minimum quantity of Shell Tivela Oil by operating under no load, then drain the system whilst Auid is warm. Repeat if necessary.
Seals, etc., should be inspected and if deteriorated then replaced. Seals previously exposed to mineral oil may shrink when exposed to Shell Tivela Oil, and therefore it may be advantageous to replace them.
Refill the system with the appropriate grade of Shell Tivela Oil. Inspect the lubricant after one or two days in use to make sure that it is free from extrane ous materials. Contamination with significant quantities of other lubricants can, in some cases, lead
to sludging, foaming and other problems.
Health & Safety
Shell Tivela Oils are unlikely to present any significant health or safety hazard when properly used in the recommended application, and good standards of industrial and personal hygiene are maintained.
For further guidance on Product Health & Safety refer to the appropriate Shell Product Safety Data Sheet. This can be obtained from your own internal Health & Safety focal point. In the event of any queries contact your local Shell Business Development Manager or:
LPDS/283
September
۱۹۹۴
UOCL/512
surfaces should be unpainted, or coated with resistant materials, for example a resistant two-pack epoxy formulation.
Shell Tivela Oils must never be mixed with mineral oil, and ideally not mixed with other polyglcol lubricants in order to preserve their anti-corrosion and demulsification properties.
Normal Office Hours
Shell Oils Delta House Wavell Road Wythenshawe
Manchester M22 5SB
Tel: 061-499-4000
Emergencies
Shell UK Ltd Downstream Oil Sheii-Mex House Strand
London WC2R ODX